ABSTRACT Visibility determination is a key requirement in a wide range of national and urban applications, such as national security, landscape management, and urban design. Mobile LiDAR point clouds can depict the urban built environment with a high level of details and accuracy. However, few three-dimensional visibility approaches have been developed for the street-level point-cloud data. Accordingly, an approach based on mobile LiDAR point clouds has been developed to map the three-dimensional visibility at the street level. The method consists of five steps: voxelization of point-cloud data, construction of lines-of-sight, construction of sectors of sight, construction of three-dimensional visible space, and calculation of volume index. The proposed approach is able to automatically measure the volume of visible space and openness at any viewpoint along a street. This approach has been applied to three study areas. The results indicated that the proposed approach enables accurate simulation of visible space as well as high-resolution (1 m × 1 m) mapping of the visible volume index. The proposed approach can make a contribution to the improvement of urban planning and design processes that aim at developing more sustainable built environments. 相似文献
AbstractWith the growing demand for underwater refill engineering, the construction technology of implementing fluidized solidification in underwater pouring has recently received increased attention. However, the environmental impact of underwater casting on surrounding water bodies, especially when the silt is polluted, is still unclear. In this study, a simulated underwater pouring test and a static immersion release test were conducted separately to study the quality of the surrounding water during and after pouring. The results showed that fluidized-solidified silt casting could increase the pH of the surrounding water, even after the pouring had stopped, by approximately 1.0 and the turbidity could reach 200 NTU. No diffusion of Zn and Cu into the surrounding water was observed and while Ni and Cr exhibited slight diffusion, this was at a level well below international water quality standard. During construction, reducing the distance from the seafloor to the bottom of the pouring catheter could reduce the level of pollution. After construction, the use of neutral solidified materials can effectively reduce the pH of the surrounding water and the potential risk of heavy metal dissolution. 相似文献
Danube loess, located at the westernmost part of the widespread Eurasian loess belt, is one of the most well-preserved aeolian dust deposits in Europe with the basal age dating back over 1 Ma. Owing to its unique location and formation processes, Danube loess plays an important role in understanding the linkage of climate changes in different climate regimes over Eurasian continent and paleoclimatic changes in middle-high northern latitudes. Major research advances of the Danube loess, including compositions, provenance, chronology, stratigraphy and paleoenvironment changes were systematically reviewed and the focuses of future research were suggested. To better understand loess provenance, the compositions of sediments in all the potential source areas should be investigated, and methodological study of provenance indicators and application of multi-proxies approaches need to be carried out. Chronologically and stratigraphically, feldspar luminescence dating and tephrochronology methods should be widely used, and the establishment of a uniform stratigraphic framework and correlation scheme should be constrained by precise chronology. In terms of the paleoenvironment, it is necessary to conduct high-resolution multi-proxies reconstruction of paleoenviroment for the entire loess-paleosol sequence, extending from the last interglacial period (130 ka to present) to interval of last 1 Ma. The future progress in Danube loess is crucial to improving the study of continental paleoclimate comparison and paleoclimate dynamics over the Eurasian loess region. 相似文献
AbstractTo achieve the rapid dewatering of dredged sludge, the flocculation–vacuum-preloading method was tested indoors. In this study, the optimal mixing ratio of six flocculants was determined through the settling column test, and then the proposed method was tested. The water drainage and settlement were monitored during the test, while the soil moisture content and shear strength were measured after the test. The results show that all the flocculants had an optimal mixing ratio, and the addition of 0.8% FeCl3 or 0.08% anionic polyacrylamide (APAM) in the sludge can better accelerate solid–liquid separation of the sludge. After the test, the water content in the sludge decreased from 140% to 60%. Compared with general vacuum preloading, the use of the proposed method increased the water drainage by 46.5% and 56.8% and decreased the soil volumes by 60.5% and 82.4% for FeCl3 and APAM, respectively. Moreover, the corresponding shear strength was increased from 10 to 14 and 17?kPa. In addition, the use of APAM increased the solidification rate of heavy metals in the sludge to more than 80%, effectively inhibiting the migration of heavy metals. 相似文献
AbstractThis study developed prestressed high-strength concrete (PHC) piles reinforced with high-strength materials (glass fiber-reinforced polymer (GFRP) bars) for flexural performance enhancement. Flexural strengths and behaviors of PHC piles reinforced with hybrid GFRP and steel bars were experimentally investigated, respectively. Large-scale specimens with total lengths of 12,000?mm and diameters of 600?mm were constructed and tested under bending, accompanied by evaluation of effects of non-prestressed reinforcement type and longitudinal reinforcement ratio. J-factors were calculated to evaluate deformability of all the specimens. PHC piles reinforced with GFRP bars were demonstrated to have much higher flexural capacity than those reinforced with steel bars. Moreover, strains at the midspans of cross sections of all the specimens basically conformed to the assumption of plane section. Failure of PHC piles reinforced with GFRP bars was attributable to gradual concrete crushing, while that of PHC piles reinforced with steel bars resulted from steel yielding. Results of this study were expected to provide theoretical basis for wide engineering applications of PHC piles reinforced with hybrid GFRP bars and steel bars in marine structures. 相似文献
The high‐precision δ60/58Ni values of twenty‐six geological reference materials, including igneous rocks, sedimentary rocks, stream sediments, soils and plants are reported. The δ60/58Ni values of all samples were determined by double‐spike MC‐ICP‐MS (Nu Plasma III). Isotope standard solution (NIST SRM 986) and geological reference materials (BHVO‐2, BCR‐2, JP‐1, PCC‐1, etc.) were used to evaluate the measurement bias and intermediate precision over a period of six months. Our results show that the intermediate precision of Ni isotope determination was 0.05‰ (2s, n = 69) for spiked NIST SRM 986 and typically 0.06‰ for actual samples, and the δ60/58Ni NIST SRM 986 values were in excellent agreement with previous studies. Eighteen high‐precision Ni isotope ratios of geological reference materials are first reported here, and their δ60/58Ni values varied from ?0.27‰ to 0.52‰, with a mean of 0.13 ± 0.34‰ (2s, n = 18). Additionally, SGR‐1b (0.56 ± 0.04‰, 2s), GSS‐1 (?0.27 ± 0.06‰, 2s), GSS‐7 (?0.11 ± 0.01‰, 2s), GSD‐10 (0.46 ± 0.06‰, 2s) and GSB‐12 (0.52 ± 0.06‰, 2s) could potentially serve as candidate reference materials for Ni isotope fractionation and comparison of Ni isotopic compositions among different laboratories. 相似文献
Decapterus maruadsi is a commercially important species in China, but has been heavily exploited in some areas. There is a growing need to develop microsatellites promoting its genetic research for the adequate management of this fishery resources. The recently developed specific-locus amplified fragment sequencing (SLAF-seq) is an efficient and high-resolution method for genome-wide microsatellite markers discovery. In this study, 28 905 microsatellites (mono- to hexa-nucleotide repeats) were identified using SLAF-seq technology, of which di-nucleotide was the most frequent (13 590, 47.02%), followed by mono-nucleotide (8 138, 28.15%), tri-nucleotide (5 727, 19.81%), tetra-nucleotide (1 104, 3.82%), pentanucleotide (234, 0.81%), and hexa-nucleotide (112, 0.39%). One hundred and thirty-two microsatellite loci (di- and tri-nucleotide) were randomly selected for amplification and polymorphism, of which 49 were highly polymorphic and well-resolved. The average number of alleles per locus was 13.63, ranging from 4 to 25, and allele sizes varied between 110 bp and 309 bp. The observed heterozygosity ( Ho ) and expected heterozygosity ( He ) ranged from 0.233 to 1.000 and from 0.374 to 0.959, with mean values of 0.738 and 0.836, respectively. The polymorphism information content (PIC) ranged from 0.341 to 0.941 (mean=0.806). However, 12 loci deviated from Hardy-Weinberg equilibrium. Furthermore, transferability tests were also successful in validating the utility of the developed markers in five phylogenetically related species of family Carangidae. A total of 48 microsatellite markers were successfully cross-amplified in Decapterus macarellus, Decapterus macrosoma, Decapterus kurroides, Trachurus japonicus, and Selaroides leptolepis. The present microsatellites provided the first known set of microsatellite DNA markers for D. maruadsi, D. macarellus, D. kurroides, and D. macrosoma, and would be useful for further population genetic and molecular phylogeny studies as well as help with the fisheries management formulation and implementation of the understudied species.
The Chagan Depression in the Yingen-Ejinaqi Basin, located at the intersection of the Paleo-Asian Ocean and the Tethys Ocean domains is an important region to gain insights on terrestrial heat flow, lithospheric thermal structure and deep geodynamic processes. Here, we compute terrestrial heat flow values in the Chagan Depression using a large set of system steady-state temperature data from four representative wells and rock thermal conductivity. We also estimate the “thermal” lithospheric thickness, mantle heat flow, ratio of mantle heat flow to surface heat flow and Moho temperature to evaluate the regional tectonic framework and deep dynamics. The results show that the heat flow in the Chagan Depression ranges from 66.5 to 69.8 mW/m2, with an average value of 68.3 ± 1.2 mW/m2. The Chagan Depression is characterized by a thin “thermal” lithosphere, high mantle heat flow, and high Moho temperature, corresponding to the lithospheric thermal structure of “cold mantle and hot crust” type. We correlate the formation of the Yingen-Ejinaqi Basin to the Early Cretaceous and Cenozoic subduction of the western Pacific Plate and the Cenozoic multiple extrusions. Our results provide new insights into the thermal structure and dynamics of the lithospheric evolution in central China. 相似文献